牛牛碰在线_国产精品一区二区免费在线观看_国产精品白嫩白嫩大学美女_欧美一级黄色录像片_av国产免费_国产手机av在线

Warranty
Mitsubishi will not be held liab
cause of Mitsubishi; machine d
products; damage, secondary
factors unpredictable by Mits
products; and to other duties.
For safe use
• This product has been manuf
industries, and has not been
device or system used in purp
• Before using the product for s
aerospace, medicine or passe
• This product has been manuf
installing the product where m
fails, install appropriate backu
This manual confers no indust
does it confer any patent lice
responsible for any problems i
a result of using the contents n
Country/Region Sales office/Tel
Mitsubishi Electric Automatio
500 Corporate Woods Parkw
Hills, IL 60061 U.S.A.
Tel : +1-847-478-2100
MELCO-TEC
Av. Paulista 1439, conj.74, B
01311-200 Sao Paulo-SP-Br
Tel : +55-11-3285-1840
Mitsubishi Electric Europe B.
Branch
Gothaer Strasse 8, D-40880
Germany
U.S.A.
Brazil
Germany
used in an environment pressurized above the
ch can be generated around the altitude of 0 m. If the
n environment, it may fail.
in any environment even outside the control panel as
of the ambient operating temperature, the ambient
e satisfied.
on of the power supply to which the equipment is
ed between the public electrical power distribution
ry within premises. Category ΙΙ applies to equipment
is supplied from fixed facilities.
nd level for up to the rated voltage of 300V is 2500V.
degree of conductive generating substances in the
e module is used. The degree of contamination 2
tion is caused by generation of only non-conductive
temporary conduction may be caused by accidental
Specification
(32 to 131°F)
°C (-13 to 167°F)
RH: Dew condensation shall not be considered.
RH: Dew condensation shall not be considered.
ermittent vibration is present
Number of times of
sweep
y Acceleration Half amplitude
10 times in each of
X, Y and Z directions
(for 80 min)
z − 0.075mm
Hz 9.8m/s2 −
ntinuous vibration is present
y Acceleration Half amplitude
z − 0.035mm
Hz 4.9m/s2 −
, 3 times in each of X, Y and Z directions
e gas shall not be present.
6561'8") or less (*1)
ntrol panel (*2)
(*3)
(*4)
5.3 Performance specifications
Output method Transistor output (Load power supply) (sink)
Number of outputs 4 points
Isolation method Isolation with photocoupler
Rated load voltage 12/24V DC
Operating load voltage
range
10.2 to 28.8 VDC (Ripple ratio: Within 5%)
Max. load current 0.1A/point, 0.4 A/1 common
Max. inrush current 0.4A/10 ms
Leakage current at OFF 0.1mA or less/30V DC
Max. voltage drop at ON 0.3V or less (typical)/0.1A
0.6V or less (max.)/0.1A
Response
time
OFF→ON 1.0ms or less
ON→OFF 1.0ms or less
Surge suppression Zener diode
Common wiring method
4 points/1 common (2 points)
(terminal block two-wire type)
Internal protection for
outputs
Internal protection circuit none
Please connect the fuse in the connected load
outside.
Item Specification
Module
power
supply
Vol tage
20.4 to 28.8V DC (24V DC -15% to +20%)
Ripple ratio: Within 5%
Current
consumption
60mA (when all points are ON)
Initial current 70mA
Max. allowable
momentary power
failure period
PS1:1ms
Number of stations
occupied
4-, 8- or 16-point mode: 1 station
Noise durability
500Vp-p
Noise width: 1µs Cycle: 25 to 60 Hz
(by noise simulator)
Withstand voltage 500V AC for 1 min
Isolation resistance
10 MΩ or more between primary area (external
DC terminal) and secondary area (internal circuit)
by 500V DC megger
Protection class IP2X
I/O part connection method Connection with terminal block
Module installation method
DIN rail installation, mounted by screws of type
M4 × 0.7mm(0.03") × 16mm(0.63") or larger
Can be installed in six directions
Mass (weight) 0.06kg (0.13lbs)
49(1.93") 4.5
(0.18")
40(1.58")
41.5(1.64") ± 0.4